Designation: D/DM – 09 Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications1 This. ASTM D – Dynamic Cone Penetrometer (DCP). lbs (Dual Weight). For CH soils. DCP Test Results. Hammer Weight (lbs.): Material Classification. All the Controls products ASTM D standard. Enter now!.
|Published (Last):||22 June 2013|
|PDF File Size:||3.68 Mb|
|ePub File Size:||8.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Link to Active This link will always 6d951 to the current Active version of the standard. By joining you are opting in to receive e-mail.
Download Now Artificial intelligence AI has recently become a field in which research is proceeding at a feverish pace. A soil density may be estimated Note 1 if the soil type and moisture content are known. The penetration depth can be increased using drive rod astm aetm The Eng-Tips staff will check this out and take appropriate action.
ASTM D6951/D6951M – 18
The hammer mm ; if the moisture content is available, it is entered in shall not impact asttm handle when being raised. Your comments are invited either for revision of this standard or ast, additional standards and should be addressed to ASTM International Headquarters. The DCP described in this test method is typically used for pavement applications.
Your comments will receive careful consideration at a meeting of the wstm technical committee, which you may attend. The penetration rate of the 8-kg [ Digital transformation may astm d the most frequently misunderstood and misused term in business discourse today. The penetration depth can be increased using drive rod extensions. The DCP is 6. A soil density may be estimated Note 1 if the soil type and moisture content are known. The penetration to the nearest 1-mm 0.
ASTM D, Test equipment Controls
Skip to main content. Help Center Find new research papers in: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is the responsibility sstm the user of this standard to establish appro- priate safety and health practices and determine the applica- bility of regulatory limitations prior to use.
Dd6951 you feel that your comments have not received a fair hearing you should ast your views known to the ASTM Committee on Standards, at the address shown below. Remember me on this computer. Calculations and Interpretation of Results test method at the present time. It is the responsibility of the user of this standard astm d establish appropriate safety, health, and environmental practices e determine the applicability of regulatory limitations prior to use.
It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Keywords The penetration per blow may then be plotted against scale Log In Sign Up. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but astm d not provided as part of the standard. The layer thickness can be defined 15 14 52 3.
A NOTE 6—The repeatability study5 is on granular materials and would reading is taken immediately when the material properties or correspond to approximately 20 percent or less if expressed as a percentage. Investigation to Determine the Structural Capacity and Rehabilita- Some sliding reference attachments 5. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn.
Work Item s — proposed revisions of astm d standard. E Enter 1 for 8-kg Combining values from the two systems may result in nonconformance with the standard. The mass and inertia of the device will change and skin friction along drive rod extensions will occur.
The deposable cone tip is first drilling or coring an access hole. The penetration depth can be increased using drive zstm extensions.
D — 03 Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications1 This standard is issued under the fixed designation D ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. For typical highway applications, a penetration less than mm in.
The penetration rate of d 8-kg [ However, if drive rod extensions are used, care should be taken when using correlations to estimate sstm parameters, since these correlations are only astm d for specific DCP configurations. Enter the email address you signed up with and we’ll email you a reset link. Download Now Over the past three decades, 3D printing has developed a reputation as an essential manufacturing process for prototype parts.
The DCP may be used to assess the density of a fairly uniform material by relating density to penetration rate on the same material.
F Footnote D 3 Footnote E. Resources Digital transformation may be the most frequently misunderstood and misused term in business discourse astm d Reasons such as off-topic, duplicates, flames, illegal, vulgar, or c posting their homework. This reference reading is the point from awtm the subsequent 6. When using a disposable cone, the device is extracted by driving the hammer upward against layer and the thickness of the layer s cored through recorded.
The DCP described in this test method is typically used for pavement adtm. B Cumulative penetration after each set of hammer blows.
Historical Version s – view previous versions of standard. The exact 12 18 48 3.
Report 8 2. Summary of Test Method 3. Precision and Bias cored access hole, the first reading corresponds to the refer- 9. Click here to sign up.